Skip to main content

DOT Inspections: How to Set Up DOT Inspections (Subscribe, Then Configure)

Turn the DOT Inspections add-on on, then configure which service templates run an inspection and which users can do them.

Written by Vladimir

Setting up DOT inspections

Two steps, and you only do them once:

  1. Subscribe to the DOT Inspections add-on.

  2. Configure it — pick which service templates run an inspection, and which users are inspectors.

You cannot skip step 2. Subscribing on its own does not put an inspection form on any job.

💡 Words that mean the same thing here. DOT Inspection, annual inspection and periodic inspection all mean the same form. Add-on and subscription both mean the paid extra you switch on in Settings. Service template and service type are the same thing.


How do I turn the DOT Inspections add-on on?

Click your profile picture (top right) → Settings → System → Subscription. Scroll down to Addons, find the DOT Inspections card and click Subscribe.

The card says exactly what you are buying: "Generate DOT inspection reports straight from the service screen. Each finalized report is billed to your subscription at the end of the billing cycle."

It is $0.99 per finished report, added to your monthly payment. It is not a monthly seat fee and it is not per location, so a slow month costs you almost nothing. The card in your own account always shows your current price.

Once you are subscribed the card shows a green SUBSCRIBED badge and the button changes to Configure.

1 = the DOT Inspections card with its SUBSCRIBED badge. 2 = the Configure button and the per-inspection price.

⚠️ I can't see Subscription in Settings. Only an Owner or an admin sees the Subscription page. Ask the shop owner to do this step, or have them check your role under Settings → System → Users.


Where do I configure DOT inspections after subscribing?

Two ways to the same page:

  • Click Configure on the DOT Inspections card, or

  • Go to Settings → Service Settings → DOT Inspection.

DOT Inspection is under Templates and Labor Rates.


What is on the DOT Inspection settings page?

Four things, and one Save button at the bottom that saves all of it:

  1. The toggle at the top right — switches DOT inspections on and off for the shop.

  2. DOT Service Templates — which service templates run an inspection.

  3. Inspectors — which users can perform and complete inspections.

  4. Save — nothing you change on this page takes effect until you click it.

1 = the on/off toggle. 2 = DOT Service Templates. 3 = Inspectors. 4 = Save.


How do I choose which service templates run a DOT inspection?

In the DOT Service Templates box, click Add a service type… and pick your DOT template from the list. The dropdown lists every service template in your shop. Then click Save.

From then on, any service item created from that template gets the inspection form.

You can nominate more than one template. If you run a federal annual inspection and a 90 day inspection off two different templates, add both. Each one gets its own line, with an × to take it off the list again.

If you do not have a DOT template yet, build one first at Settings → Service Settings → Templates → + New Service Type: name it DOT Inspection, set the duration you actually book (45 minutes is typical) and your rate. Every field on that form works like any other template — see Service Templates: How to Create and Use Them. Then come back here and add it.


Do I still need to set the Labor Type to "DOT Inspection"?

No. That is the old way and it no longer switches the form on.

⚠️ This changed. DOT inspections used to be switched on by opening a service template and setting its Labor Type to DOT Inspection. That is no longer how it works. The only thing that decides whether a template runs an inspection is whether the template is listed under DOT Service Templates on Settings → Service Settings → DOT Inspection. If you followed older instructions and set a labor type, nothing is broken — just add the template to the list on the DOT Inspection page as well.


How do I choose who can run DOT inspections?

In the Inspectors box, click Add a user… and pick the user. The description on the page says it plainly: "Select which users can perform and complete DOT inspections." Click Save.

There is a second half to this — each user also has two DOT permissions on their own profile. Both halves need to be set. See Who Can Run and Complete a DOT Inspection.


What does the toggle at the top of the page do?

It switches DOT inspections on and off for the whole shop. It is on once you subscribe. Leave it on — turning it off is how you stop inspection forms appearing without unsubscribing from the add-on.


I set it all up and there is still no Inspection Form button

Work down this list in order:

  1. Is the add-on SUBSCRIBED on Settings → System → Subscription → Addons?

  2. Is the toggle at the top of Settings → Service Settings → DOT Inspection on?

  3. Is the template you used listed under DOT Service Templates? This is the one people miss.

  4. Did you click Save after adding it?

  5. Did you add the service item using that exact template? A service item typed in by hand instead of picked from the template list will not get a form.

  6. Are you the right user? A user who is not on the Inspectors list, or who is missing the View and Edit DOT Inspections permission, does not get the button at all — it is not greyed out, it is simply absent. See Who Can Run and Complete a DOT Inspection.

💡 Quick way to tell those last two apart: have an Owner look at the same job. If the Owner sees the Inspection Form button and the mechanic does not, it is the mechanic's DOT access. If nobody sees it, it is the template not being on the DOT Service Templates list.

Still nothing? Message us from the chat bubble in the app and tell us the service number — we will look at it.


Quick answers

"Does subscribing put the form on my jobs straight away?" — No. You still have to add your template under DOT Service Templates and click Save.

"Does the truck have to be checked in before the Inspection Form appears?" — No. The button is there as soon as the DOT service item exists, even on a job sitting in Upcoming that has never been checked in.

"How much does it cost?" — $0.99 per finished report, added to your monthly payment. Nothing is charged for an inspection you start and never finish.

"Is it charged per location or per user?" — Neither. It is charged per finished report.

"Can I have two DOT templates?" — Yes. Add as many templates as you like to the DOT Service Templates list.

"Where did the DOT labor type setting go?" — It is no longer used to switch the form on. Use the DOT Service Templates list instead.

"Do I have to do this for each shop location?" — The DOT Inspection settings page is under Service Settings for the account. If you run more than one location and the setup does not look right at one of them, message us and we will check it with you.


Related articles

Did this answer your question?