Somebody walks in with a starter to rebuild, or a hose to make up, and you just want to bill them. Typing in a whole new company and a whole new truck for a ten-minute job feels like a waste of time — and it is.
Every work order in EasyTruckShop needs a company and a vehicle. There is no way around that. But you only have to do the setup once. Build one reusable customer and one reusable vehicle, and from then on a walk-in job takes three clicks.
First — should you use this?
If you will ever see this customer again, create them properly. A real customer and a real vehicle is what gives you service history on that truck, invoices under their name, PM schedules, and a way to find the job again in six months when they call about it. That record is the whole point of the software, and it takes two minutes.
Use the shortcut below for one-off, walk-in, pay-on-the-spot work where speed matters more than the record. Use a real customer and vehicle for everybody else.
Step 1 — Create the customer (once)
Go to Customers → Companies and click + New Customer.
In Name, type Cash Account.
Fill in the Contact section. E-mail and Phone are required — use your own shop's email and phone, since there is no single real person behind this account. A contact name like Cash Customer works well.
Click Save.
Call it whatever suits your shop — Cash Account, Walk-In, Counter Sale. Just pick one name and stick to it so everyone uses the same account.
Step 2 — Add one vehicle called General (once)
This is the part most people do not realise: on a new vehicle, only Company and Unit are required. VIN, licence plate, make, model and year can all be left blank.
On the Cash Account customer, open the Vehicles tab and click + Add Vehicle.
In Unit, type General.
Leave VIN, Licence Plate, Make, Model, Year and the rest blank.
Turn Track Odometer off. If you leave it on, EasyTruckShop asks you for a mileage reading every single time you check this vehicle in — which defeats the point.
Click Save.
In the picture below: 1 = the Company, already filled in as Cash Account. 2 = the Unit field, the only other thing you must type. 3 = Track Odometer, switched off. 4 = Make, Model and Year, all left empty.
Step 3 — Use it, in three clicks
That is the setup done, for good. From now on, a walk-in job goes like this:
Go to Services and click + New Service.
In Company, start typing Cash and pick Cash Account. The contact fills itself in.
In Vehicle, pick General. It is the only one on the account, so it is one click.
Type the job into the Complaint box and click Check-in.
In the picture below: 1 = Company set to Cash Account. 2 = Vehicle set to General. 3 = the Complaint, with the real customer's name and phone number in brackets.
How do I remember who the job was actually for?
Put the person's name and phone number in brackets at the end of the complaint, like this:
Rebuild starter motor — bench repair (John Miller, 555-341-8890)
The complaint text follows the job all the way through: it shows on the work order, it prints on the invoice, and it is searchable. So even though the invoice is addressed to Cash Account, you can still tell at a glance whose starter it was, and you can find it again by searching the name.
Do it the same way every time and it becomes a habit your whole shop can rely on.
What this does NOT give you
This is a shortcut, and it costs you things. Know what you are giving up:
No real service history. Every walk-in job piles onto the same General unit, so the vehicle's Service History becomes a mixed list of unrelated jobs.
The invoice says Cash Account. It will not carry the customer's own name in the address block — only inside the complaint text where you typed it.
No mileage, no PM schedules. With Track Odometer off there is nothing to base a PM interval on, which is correct for this account but means General can never be used for preventive maintenance.
It does not remove the vehicle requirement. There is still a vehicle on the work order — you have just made one you can reuse instead of creating a new one each time.
It is not for repeat customers. The second time somebody comes back, make them a real customer.
Selling a part with no labour? You may not want a work order at all — Parts → Sales → + New Sale is built for counter sales.
Quick answers
"It won't let me save the vehicle." → Unit is required. Type something in it — General is fine.
"It keeps asking me for mileage at check-in." → Track Odometer is still on for that vehicle. Open the vehicle, click Edit, and switch it off.
"It won't let me save the customer." → E-mail and Phone are required on the contact. Use your own shop's.
"Can I have more than one of these?" → Yes. Some shops add a second unit such as Bench or Shop under the same Cash Account to keep counter work and bench work apart.
"How do I find an old walk-in job?" → Search the customer's name in the top search bar. It will find the complaint text you typed in brackets.
Other ways shops ask this question
"Can I make a work order without creating a vehicle?"
"Do I have to add a customer every time?"
"How do I bill a walk-in customer quickly?"
"Someone brought in a part to fix — there is no truck."
"How do I do a cash sale?"
"Creating a new customer and vehicle takes too long."
"Can I skip the VIN and the make and model?"
"How do I write up bench work?"
"Is there a generic customer I can use?"
"Why is the vehicle field required?"
Related Articles
How to Add a Vehicle to a Customer — the full vehicle form, including what the VIN lookup fills in for you
Service Flow: Where to Create a New Service and What to Fill In — every field on the New Service page
Service Flow: Save as Upcoming vs Check-in — which button to use when the job is not starting yet



